Rolled wheel center hubs for mainline diesel-electric locomotives 2ТE10, 2ТE116

Given below are results of development and implementation of a pilot batch of rolled wheel center hubs made of steel grade ‘S’ at the JSC VMZ Iron and Steel Works designed to replace stock-produced cast wheel center hubs in mainline diesel-electric locomotives 2ТE10, 2ТE116. Flow line production of rolled wheel center hubs includes a mill for rolling center disk-type wheels where wheel center hubs are made of medium carbon/low-alloy steel with further heat treatment (namely normalizing and stress relieving). The rolled wheel center hubs have an optimized low-stress configuration and are supplied with all its surfaces machined. Within the standard routine preceding mass production, the rolled centers were tested in a laboratory where a full package of mechanical properties were analyzed, were tested on a rig for crack resistance (or fracture toughness), also a pilot lot was tested on the Experimental Loop (JSC VNIIZhT) and were tested in revenue operations performed by Severnaya Railway Operator where they were installed in the wheels of diesel-electric locomotives. Test results have shown that the new rolled wheel center hubs made of steel grade ‘S’ demonstrated improved reliability in revenue operations due to higher steel quality and higher parameters of strength, fatigue life and fracture toughness. Additionally, the use of a new steel grade, optimized center hub design, and a new manufacturing technology - rolling instead of casting - have resulted in a substantial cuts of wheel centers production costs and a 10 % decrease of assembled weight. Due to positive results of tests in revenue operations the company JSC VMZ has held the acceptance test procedure related to rolled wheel center hubs made of steel grade ‘S’ and registered a permit to manufacture as much as a preproduction batch. Results of this work have been taken as a basis for the new standard GOST R 55498 - 2013 ‘Rolled wheel center hubs for the railway rolling stock. Technical specifications’.

motive power, rolled wheel center hub, medium carbon steel, mechanical properties, fracture toughness, stress-strained condition, low-stress construction, rig tests and field trials

1. Zhuchkov S. M., Kuz’michev V. M. Zamena litykh tsentrov lokomotivnykh koles na katanye: preimushchestva i zadachi [Replacing cast centers of locomotive wheels for rolled ones: Benefits and challenges]. Metallurgicheskie protsessy i oborudovanie, 2007, no. 3, pp. 11 – 14.

2. Zhuchkov S. M. et al. Puti povysheniya konstruktsionnoy prochnosti kolesnykh tsentrov [Ways to increase the structural strength of the wheel centers]. Metallurgicheskie protsessy i oborudovanie, 2008, no. 4, pp. 13 – 16.

3. Zhuchkov S. M., Kuz’michev V. M., Perkov O. N. Tekhnologicheskie vozmozhnosti zameny litykh tsentrov lokomotivnykh koles katanymi [Technological feasibility of replacing cast centers of locomotive wheels by rolled ones]. Metallurgicheskie protsessy i oborudovanie, 2007, no. 4, pp. 23 – 25.

4. Zhuchkov S. M., Kuz’michev V. M., Perkov O. N. Osobennosti realizatsii tekhnologii izgotovleniya kolesnykh tsentrov dlya lokomotivov metodom obrabotki davleniem [Features of the implementation of production technology of wheel centers for locomotives by forming]. Fundamental’nye i prikladnye problemy chernoy metallurgii. Sb. nauch. tr. [Fundamental and applied problems of ferrous metallurgy. Coll. sci. pap.], 2008, no. 17, pp. 240 – 244.

5. Fermer M. Optimisation of a railway freight car wheel by use of a fractional factorial design method. Proceedings of Institution of Mechanical Engineers, 1994, vol. 308, pp. 97 – 107.

6. Procedure for the Analytic Evaluation of Locomotive and Freight Car Wheel Designs, S-660 – 83. Washington, DC, Association of American Railroads.

7. Volokhov G. M., Kerentsev D. E. Razvitie metodov otsenki prochnosti konstruktsiy tsel’nokatanykh zheleznodorozhnykh koles i kriteriev ikh dopuska k ekspluatatsii pary [Development of methods to assess the strength of structures of solid-rolled railway wheels and criteria for the admission to operation as a pair]. Vestnik VELNII [Bulletin of the Russian Research and Design Institute of Electric Locomotive Building], 2013, no. 2, pp. 138 – 154.

8. Borodin A. V., Zdor G. P., Yarysheva L. V. Analiz prochnosti soedineniya “kolesnyy tsentr — bandazh kolesa teplovoza” [The analysis of the strength of “wheel center — bandage of the locomotive wheels”]. Izvestiya Transsiba, 2012, no. 1, pp. 8 – 12.

9. Golyshkov R. A., Kerentsev D. E. Railway wheel. Patent RUS 2428319. April 07, 2010. (in Russ.).

10. Instructions for the formation, repair and maintenance of wheel pairs of traction rolling stock of 1520 mm DH-329. Moscow, Tekhinform Publ., 2000. 136 p. (in Russ.).

11. Wheelsets of traction rolling stock of 1520 mm. Instructions for use, maintenance and repair of KMBSH. 667120.001RE. 2005

12. Borodin A. V., Zdor G. P., Yarysheva L. V. Vliyanie usloviy ekspluatatsii na prochnost’ soedineniya “kolesnyy tsentr — bandazh” kolesa teplovoza [Effect of operating conditions on the strength of “wheel center — bandage” of the locomotive wheel]. Transport Urala, 2013, no. 2, pp. 55 – 58.